Baumfolder BAUM20: Ifold Service Manual Uživatelský manuál

IFOLD SERVICE MANUAL TP10497

15. Run wire 4L1 to K2-53 if folder is a 15” or 18” model or to K2-53 if folder is a 20” model. Run 4L2 toK2-83 if folder is a 15” or 18” model or to

16. Cleanup wiring and reinstall all wire channel covers that were removed. 17. Replace DCT500 software chip, shown in Figure 9. Carefully do this

18. Move the run/main jumper (currently on the 1st and 2nd pins) to the 2nd and 3rd pins; this will place the machine in maintenance mode at power up

1122. Go to the advance settings by pressing button 3, Figure 10. Value A00 should now be displayed in display 1. Use button 4 and button 5 to chang

ifold machine configuration instructions For service technicians use only Page 12 of 45TP10497

The first time ifold is powered up the Machine Configuration button will appear on the start up screen. Touch this button to configure for your machin

This should be set from the factory. 0 = Autoset 1 = 2015 2 = 2020 pile 3 = 2020 continuous 4 = 1526 or 1530 Once the number of plates in the Paralle

Touch this box to tell Ifold if you have the optional Gatefold plate. It will toggle between yes and no each time it is touched. Touch this box to tel

You can get back into the Machine Configuration screen at anytime by going to the main page then touching the Maintenance button Once in the Maintena

Start up procedures The I-Fold software should start-up automatically when the machine is turned on. If for any reason it does not start up properl

TABLE OF CONTENCE IFOLD ELECTRICAL INSTALATION……...PAGE 3 IFOLD MACHINE CONFIGURATION…...PAGE 12 IFOLD STAR

Touch this button to go to the summary screen for the current job. The summary screen shows all of your settings and any notes you want to add Touch

Touch this button to bring up a job calculator that will help you determine how long a job will take. When this box is red it indicates you have made

If this is the first time you have logged on touch the NEW button then type your name and touch enter. It will ask for a password, if you do not ente

This box show the available folds. Touch a button to see the fold in the box on the left. Touch the ► Arrow at the bottom of the page to see the next

Touch one of these boxes to select a paper size. A on the button indicates that paper size will not run on your machine This box shows how the pape

Touch this box once the desired paper size and orientation have been selected. The text will change from select this paper size and orientation to fol

This will come up on the left of any setup screen when the see setup list button is touched. This list shows all of the setup screens needed for the

These areas show the number of sheets that go under each gapset and the fold plate settings for every station required to do the selected fold. The bl

In this area you can enter up to 4 notes with up to 55 characters per note to be saved with a fold job. These could contain information like what spee

Use the keypad to enter a note, the clear button will clear everything in the display, this is recommended if you are entering a new note. The Ins/Del

I-FOLD ELECTRICAL INSTALLATION 1. WARNING: Power MUST BE DISCONNECTED from the machine before starting this procedure. 2. Remove the back feeder,

This will come up on the left of any setup screen when the see setup list button is touched. This list shows all of the setup screens needed for the

4 boxes show the settings for the fold plates. To make a change to one of the settings just touch the box you wish to change and a keypad will pop up.

This line indicates the fold plate you are making a change to This is the current setting (0 or blank = deflect). If a number is displayed touch the

This line indicates the gapset you are making a change to. This is the current setting touch the C to clear it then enter the desired number. Touch d

These boxes tell you how many days are left until the maintenance item needs done. The grease canister is fixed all the others can be set as desired.

Touch this box to enter the folder speed you plan to run the job. The default is 60% of full speed. Touch the SEE HOW button to find out how to read

DESCRIPTION:UNIT NAME:REV:ASSEMBLY NUMBER:SHEET OFIFOLD DISPLAYBAUMFOLDERCORPORATIONIFOLD DISPLAY MOUNTING LOCATION1 1Page 34 of 45TP10

DESCRIPTION:UNIT NAME:REV:ASSEMBLY NUMBER:SHEET OFIFOLD DISPLAYBAUMFOLDERCORPORATIONFK2001484IFOLD DISPLAY ADAPTOR KIT1 2Page 35 of 45T

DESCRIPTION:UNIT NAME:REV:ASSEMBLY NUMBER:SHEET OFIFOLD DISPLAYBAUMFOLDERCORPORATIONFK2001484IFOLD DISPLAY ADAPTOR KIT2 2Page 36 of 45T

DESCRIPTION:UNIT NAME:REV:ASSEMBLY NUMBER:SHEET OFIFOLD DISPLAYBAUMFOLDERCORPORATIONFK2001485IFOLD DISPLAY MOUNT1 2Page 37 of 45TP10497

4. Install mounting arm into display mount. 5. Mount computer and enclosure onto mounting arm as shown in figure 3. 6. Remove Bottom cover plate

DESCRIPTION:UNIT NAME:REV:ASSEMBLY NUMBER:SHEET OFIFOLD DISPLAYBAUMFOLDERCORPORATIONFK2001485IFOLD DISPLAY MOUNT2 2Page 38 of 45TP10497

DESCRIPTION:UNIT NAME:REV:ASSEMBLY NUMBER:SHEET OFIFOLD DISPLAYBAUMFOLDERCORPORATIONFK2001370DISPLAY-ENCLOSURE1 2Page 39 of 45TP10497

DESCRIPTION:UNIT NAME:REV:ASSEMBLY NUMBER:SHEET OFIFOLD DISPLAYBAUMFOLDERCORPORATIONFK2001370DISPLAY-ENCLOSURE2 2Page 40 of 45TP10497

DESCRIPTION:UNIT NAME:REV:ASSEMBLY NUMBER:SHEET OFIFOLD DISPLAYBAUMFOLDERCORPORATIONFK2001426IFOLD DISPLAY MOUNT1 2Page 41 of 45TP10497

DESCRIPTION:UNIT NAME:REV:ASSEMBLY NUMBER:SHEET OFIFOLD DISPLAYBAUMFOLDERCORPORATIONFK2001426IFOLD DISPLAY MOUNT2 2Page 42 of 45TP10497

DESCRIPTION:UNIT NAME:REV:ASSEMBLY NUMBER:SHEET OFIFOLD DISPLAYBAUMFOLDERCORPORATIONFK2001500CABLE ASSY. POWER1 1Page 43 of 45TP10497

DESCRIPTION:UNIT NAME:REV:ASSEMBLY NUMBER:SHEET OFIFOLD DISPLAYBAUMFOLDERCORPORATIONFK2001501CABLE ASSY. COMMUNICATIONS1 1Page 44 of 45

DESCRIPTION:UNIT NAME:REV:ASSEMBLY NUMBER:SHEET OFIFOLD DISPLAYBAUMFOLDERCORPORATIONFK7600179SCHEMATIC-IFOLD1 1Page 45 of 45TP10497

Figure 3 10. Mount the 2 cable anchors, as shown in Figure 4

Figure 4 Cable Anchor Wire Tie Wire Channel Strain Reliefs 4Pa

11. The communication board will sit on the right side of din rail that sits above the transformer, as shown in Figure 5. Run the communication cabl

Figure 6 1234910 Ribbon Cable Communication Board Communication Cable Terminal Block DCT500 PinkGray Brown Whit

Figure 7 A-F1 4L1 A-F2 4L2