Baumfolder BAUM18: Pile Folder 1st Station (from 2005 on) Uživatelský manuál

PAGE 1 TP10313BAUM 20181ST STATION FOLDER W/PILE FEEDINSTRUCTION MANUAL©Baumf

TP10313 PAGE 10OPERATOR CONTROLSThe main operator control panel (Figure 8) is located atthe pile feeder. See the "Control Panel" section for

PAGE 11 TP103131.0 Control Panel BAN-5Figure 1. Control Panel.1.1 Displays01

TP10313 PAGE 121.4 Keypad Buttons with Selection Indicators18) Show Output Count19) Show Batch Count and Number of Batches20) Show Current Rate21) Sh

PAGE 13 TP103132.1.1 Machine Setup ParametersTable 1. Machine Setup Paramet

TP10313 PAGE 142.1.3 Machine Setup ParametersTable 3. Machine Setup Parameter ListP20: Units of MeasurementThis selection specifies the unit of meas

PAGE 15 TP10313P28: Serial Output TypeThis selection, in maintenance mode, sh

TP10313 PAGE 162.1.6 Machine UsageStatus ParametersTable 6. Machine Usage Status Parameter ListP50: Power On TimeThis selection shows the time in 1/10

PAGE 17 TP10313Batching Time AdjustmentThe batching time adjustments allow th

TP10313 PAGE 18Table 10. Suction Mode SymbolsTable 11. Suction Length FunctionTWT-180 ModeLeading Edge ControlLeading and Trailing Edge Control+++If

PAGE 19 TP103132.7 Production ModeEnter Run Mode and Select Large Display Con

TP10313 PAGE 2WARNING Do not operate this machine without all guarding in place. Do not make adjustments or perform maintenance on this machine with

TP10313 PAGE 20Reset FunctionPressing and holding this key will result in a resetfunction being activated after a 5-second countdown. Thefunction is

PAGE 21 TP103134.0 Process Variables Definitions4.1 Total Input CountTotal In

TP10313 PAGE 225.3 Batch Output TimeThis parameter, accessible in the Batch Setup mode,specifies the output duration or delay that will be used whent

PAGE 23 TP103136.0 System Messages and Run Messages6.1 Power-Up Fault Message

TP10313 PAGE 246.2 Run Time Fault MessagesRun time fault messages are only displayed when the unit is in Run mode. Fault errors can still occur, but t

PAGE 25 TP103136.3 Machine Run Error MessagesMachine Run Error Messages help

TP10313 PAGE 26PILE FEEDER OPERATION1.0 Loading the Pile FeederSet the right hand side guide (Figure 11-1) to half thesheet using the scale (11-2). T

PAGE 27 TP103131.3 FRONT BLOW TUBE SETTINGSThe front blow consists of two tu

TP10313 PAGE 28Figure 18REGISTER OPERATION Use the fluted knob (Figure 19-1) to slide the side guide(19-2) with the marble holder (19-3) to the re

PAGE 29 TP10313Figure 21BAUMSET ADJUSTMENT1.0 Adjustment of Folding Rollers

PAGE 3 TP10313CONTENTSDESCRIPTION PAGEI.) Safety ...

TP10313 PAGE 30SETTING OF FOLD PLATESNOTE:Check the symbols on the fold plate stop (Figure 23-1) forinstallation of the fold plate swing deflectors (F

PAGE 31 TP10313Check that the adjustment screws (26-4) are in contact withthe

TP10313 PAGE 32SCORING/SLITTING/PERFORATING Your new folder is capable of many different applicationsthat compliment the folding performance and p

PAGE 33 TP10313so that the fold is made with, rather than against thescoring,

TP10313 PAGE 341.3 Slitting (Cutting) Sheets Folders may be used to cut folded or flat sheets apart.The general set up for blades and collars is

PAGE 35 TP103131.4 Trimming Edges of Booklets Figure 38 shows the setup

TP10313 PAGE 36LUBRICATION/MAINTENANCEPile FeederVacuum Solenoid Valve The vacuum at the suction wheel is controlled by asolenoid valve (Figure 40). T

PAGE 37 TP10313TECHNICAL SPECIFICATIONSBAUM 2018Maximum sheet size 20.5"

TP10313 PAGE 38TROUBLESHOOTINGPROBLEM CAUSE REMEDYSheets stick together Inadequate ink drying, cut Fan out thoroughly whenparticularly along sides. wi

PAGE 39 TP10313TROUBLESHOOTING - continuedPROBLEM CAUSE REMEDYSheets fails to

TP10313 PAGE 4CONTENTSDESCRIPTION PAGEIX.) Pile Feeder Operation ...

TP10313 PAGE 40screws for the slitter shaft accessories facing out, so youdon't have to turn the shafts to get to the screws.OPERATING TIPSSetup

PAGE 41 TP10313Fixing Crooked Perforations If misaligned perforations app

TP10313 PAGE 42Principles of Mechanical FoldingThe buckle folding principle In buckle folding, each station consists of three rollersand a buckle

PAGE 43 TP10313IMPOSITIONS18 MOSTPOPULAR FOLDS12345MAINDRIVEFOLD PAN #1FOLD P

TP10313 PAGE 44On a buckle folder, the sheet is laid flat on a register table and then enters the fold pan assemblywhere it comes to a stop against th

PAGE 45 TP10313MANUAL USAGEUse this manual when you need to know how to set-u

TP10313 PAGE 46TYPICAL LAYOUT ANDSHEET ORIENTATIONEach numbered Imposition Blockin this manual contains:A. Imposition TitleB. Fold Pans UsedC. Sheet L

PAGE 47 TP1031312346512346578123465784-PAGEParallel: 1May be folded two ormor

TP10313 PAGE 4812BCCB7891043651211111291043216598ABBCCA1234657812346578346512788-PAGE, TWO RIGHTANGLE OBLONGParallel: 18-Page: 178-PAGE, RIGHTANGLE

PAGE 49 TP1031312346578111291014131516123478222118176511129101413151623241920

PAGE 5 TP10313List of TablesDESCRIPTION PAGETable 1. Machine Setup Parameter

TP10313 PAGE 50Baumfolder has authorized dealers located through-out the United States.Call toll free, 1-800/543-6107 for parts or thenumber of your

TP10313 PAGE 6SAFETY FIRSTYour new Baum paper folding machine has been designedin accordance with the latest safety specifications. Thewarning and ca

PAGE 7 TP10313WARNING LABELSWARNINGGUARD MISSINGDO NOT OPERATE50944WARNINGGUA

TP10313 PAGE 8INTRODUCTION OVERVIEWThe 1st station [parallel] folder with pile feedercontains the following main components (Figure 1):1. Pile Feeder2

PAGE 9 TP10313ELECTRICAL CONNECTIONS1.0 Wiring the Pump (2018 / 1 phase)Conne